Roland SONAR V-STUDIO VS-100 Manual de usuario

Hardware ManualVS-100_r_e.book 1 ページ ２００９年３月２５日　水曜日　午前９時３４分

10Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (Hardware manual p. 3; p. 6). These sec

11 OverviewVS-100_r_e.book 11 ページ ２００９年３月２５日　水曜日　午前９時３４分

12 Overview of the SONAR V-STUDIO 100 fig.fader.eps High-end spec audio interface functions • USB 2.0 audio interface supporting 8-in/6-out and 24-bi

13 Overview of the SONAR V-STUDIO 100 fig.fader.eps A digital mixer that supports a range of inputs • A digital mixer with 8 channel input• High qual

14 Panel Descriptions fig.front01.eps 1. INPUT 1L/INPUT 2R Analog audio signal input jacks with a microphone preamp.You can use the [SENS] knob to ad

15 Panel Descriptions fig.rear01.eps 4. Cord hook Hook the AC adapter’s cord here, see p. 38. 5. Power switch Turn the power on/off. For more informa

16 Panel Descriptions INPUT fig.rear02.eps 11. INPUT 3L/MONO and 4R (1/4” TRS balanced input) Analog audio signal input jacks for line input. If you

17 Panel Descriptions fig.mixer01.epsfig.01.eps 1. [PAN] knob (INPUT 1L/INPUT 2R) Use this knob to adjust the balance between the right and left chan

18 Panel Descriptions fig.02.eps 5. Compressor/equalizer setting button Use this button to switch the display on the setting screen between the compr

19 fig.mixer03.eps If you connect SONAR V-STUDIO 100 to a computer and turn the power on, the section within the bounding rectangle in this illustrat

VS-100_r_e.book 2 ページ ２００９年３月２５日　水曜日　午前９時３４分

20 fig.daw01.eps This section controls SONAR’s track or bus parameters. 1. Track selection button Use this button to select the track (or bus) to con

21 4. Channel fader Use this to control the volume of the current strip.The channel fader has a touch-sensitive motor fader so it can move in respons

22 fig.daw02.eps This section controls playback of SONAR. 1. [LOOP] button Press this button to turn SONAR’s loop function on or off.* This button is

23 fig.daw03.eps When you press the [ACT] button to turn on the ACT function, the button lights up and you can use the [R1]–[R4] knobs to control the

24 fig.proppage.eps The VS-100 properties page displays the names of the parameters that can be controlled with the [R1]–[R4] knobs.You can also conf

25 WAVE RecorderVS-100_r_e.book 25 ページ ２００９年３月２５日　水曜日　午前９時３４分

26 Using the WAVE recorder fig.mixer04.eps When you turn on the power of the SONAR V-STUDIO 100 without connecting it to a computer, the [DAW/WAVE RE

27 Using the WAVE recorder Information displayed on the main screen fig.recorder02.eps 1. File name2. Level meter• Displays the output level• When in

28 Using the WAVE recorder In SONAR V-STUDIO 100, data is recorded on an SD memory card. Inserting an SD memory card fig.sd-ins.eps NEVER insert or r

29 Using the WAVE recorder 1. Check the input level. fig.recorder04.eps If the peak indicator at the right end of the level meter (indicated by the a

3 USING THE UNIT SAFELY •Do not open (or modify in any way) the unit or its AC adaptor. ...

30 Using the WAVE recorder 1. Press the (Playback) button. 2. Use the [PLAYBACK] knob to adjust the playback volume. If the sampling frequency of t

31 Using the WAVE recorder The finder screen lets you view the file size and file format. 1. From the main screen, press the [CURSOR/VALUE] knob to o

32 Using the WAVE recorder During playback or recording, you can insert markers at any point on the file.By inserting markers on a file, you can quic

33 Using the WAVE recorder This function allows you to play back any section (A-B) in the file repeatedly. After inserting marks A and B while the fi

34 Using the WAVE recorder 1. Press the [METRONOME] button. The metronome function is turned on and the [METRONOME] button flashes. 2. The metronome

35 Using the WAVE recorder You can play back a file in the background and record only your playing at the same time. 1. Select the file to play back

36 Using the WAVE recorder A deleted file cannot be recovered. 1. From the main screen, press the [CURSOR/VALUE] knob to access the finder screen (p.

37 ConnectionsVS-100_r_e.book 37 ページ ２００９年３月２５日　水曜日　午前９時３４分

38 Connections Connect the included AC adaptor to the SONAR V-STUDIO 100’s DC IN jack. fig.Connect-ACadpt.eps Place the AC adaptor so the side with t

39 Connections • Use a USB cable to connect your computer to the SONAR V-STUDIO 100.• Connect your audio output devices such as headphones or speaker

4 USING THE UNIT SAFELY •Be sure to use only the AC adaptor supplied with the unit. Also, make sure the line voltage at the installation matches the

40 Turning the power on * Once the connections have been completed (p. 38), turn on power to your various devices in the order specified. By turning

41 Connections and signal flow fig.Connect-mic-guitar.eps * To prevent malfunction and/or damage to speakers or other devices, always turn down the v

42 Connections and signal flow Signal flow when recording with SONAR fig.routing01.eps If you connect the SONAR V-STUDIO 100 to your computer with a

43 Connections and signal flow fig.Connect-various.eps * The sampling frequency of the input signal from digital equipment must be the same as that o

44 Connections and signal flow Signal flow when recording with SONAR fig.routing03.eps • To control the direct monitor volume for the input signal, u

45 Connections and signal flow Signal flow when recording with the WAVE recorder fig.routing04.eps • Signals input to INPUT 1–8 are mixed and recorde

46 Connections and signal flow fig.connectFS.eps You can use footswitches to control the actions of the WAVE recorder and SONAR. If you are using SON

47 Compressor and EqualizerVS-100_r_e.book 47 ページ ２００９年３月２５日　水曜日　午前９時３４分

48 Using the compressors and equalizers Each analog input on SONAR V-STUDIO 100 is equipped with a compressor and a 3-band equalizer. fig.compEQ01.ep

49 Using the compressors and equalizers fig.compEQ03.eps Pressing the compressor/equalizer toggle button switches between the screens for the compres

5 USING THE UNIT SAFELY •The unit and the AC adaptor should be located so their location or position does not interfere with their proper ventilation

50 Using the compressors and equalizers fig.compEQ06.eps Setting the compressors MeaningChanging the settings 1 Channel currently displayed Press the

51 AppendixVS-100_r_e.book 51 ページ ２００９年３月２５日　水曜日　午前９時３４分

52 System settings An SD memory card that you have just purchased or an SD memory card that has been used by a computer or other device must be forma

53 System settings The digital mixer section provides reverb that can be applied to the signal from each input.When you execute the system setting “R

54 System settings To initialize all settings of SONAR V-STUDIO 100 to their factory-set state, proceed as follows. The data in the SD memory card wi

55 System settings Parameter list ParameterDescription Value LCD ContrastAdjusts the contrast of the display.Higher values will make the display appe

56 LINE INMAIN MIXMAINMIXL INR INCHANNEL 3&4MIC IN213PHANTOM POWERSENSLEVELMIDLOFREQQHIR INRCAL INPANLEVEL1234562CHANNEL 5&6COAXIAL INCHANNE

57 About V-LINK What is V-LINK? V-LINK () is functionality that allows you to perform music and video simultaneously. By connecting V-LINK compatible

58 Error Message List SD Card Slow/Push Any Key fig.sd-card-slow.eps Recording into the WAVE recorder was halted because writing to the SD memory car

59 Error Message List Improper File fig.improper-file.eps The selected file cannot be played by the SONAR V-STUDIO 100. Action: • Use SONAR or other

6 IMPORTANT NOTES Power Supply • Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled

60 Specifications Digital Audio Workstation: SONAR V-STUDIO 100 Audio Interface, Mixer Number of Input Channels8AD/DA ConversionSample Rate: 44.1/48

61 Specifications * 0 dBu = 0.775 Vrms* In the interest of product improvement, the specifications and/or appearance of this unit are subject to chan

62 Index A AB button ... 27AC adaptor ...

63 Index P PAN knob ... 17Phantom Power ... 14, 16Play but

64This product complies with the requirements of EMC Directive 2004/108/EC.For EU CountriesFor CanadaThis Class B digital apparatus meets all require

65IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.BLUE: BROWN: As the colours of the wires in the mains le

66For ChinaVS-100_r_e.book 66 ページ ２００９年３月２５日　水曜日　午前９時３４分

InformationAs of Jan. 1, 2009 (Cakewalk)Information When you need repair service, call your nearest EDIROL/Roland Service Center or authorized Cake

* 5 1 0 0 0 0 6 4 0 9 - 0 2 *VS-100_r_e.book 68 ページ ２００９年３月２５日　水曜日　午前９時３４分

7 IMPORTANT NOTES Using SD Memory Cards • Carefully insert the SD memory card all the way in—until it is firmly in place.• Never touch the terminals

8 Contents USING THE UNIT SAFELY.......3IMPORTAN

9 Connections.................... 37 Connections ...........