Roland TMC-6 El manual del propietario

Owner’s Manual 201a Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” (p. 2–3) and “IMPORTANT NOTES” (p. 4). The

10 Restoring the Factory Settings (FACTORY RESET) This procedure restores the original, factory-set values stored in the TMC-6. 1. While holding down

11 Making the Pad Settings When initially making the settings of the TMC-6, first: 1. Select a TRIG TYPE (Trigger Type) parameter suitable for the co

12Making the Pad SettingsSelecting from the TMC-6’s panel (Trigger Chase OFF)1. Press the [EDIT] button to make its indicator light.This takes you int

13Making the Pad SettingsEditing MIDI ParametersOnce you have connected the pads and selected the appropriate trigger type, then match the MIDI channe

14Example of Connections and SettingsHere is an introductory example of actual settings using the TMC-6.Adding a Pad to a Drum ModuleYou can use the T

15Example of Connections and Settings2. Confirm which of the TD-10 and TMC-6 the pad is connected to.When you strike the pads connected to the TD-10,

16Example of Connections and Settings[TD]8. With the right [CURSOR], move the cursor to the instrument name.[TMC]9. Set the note number transmitted by

17Example of Connections and Settings(2) About Switching Percussion SetsOn the TD-8/6, percussion sets are set for each pattern or song, and cannot be

18Example of Connections and SettingsAdvanced Methods of Using Pads Connecting a PD-80R/PD-120 to a TRIGGER INPUT Other Than TRIG 2 If TRIG 2 is alre

19Example of Connections and Settings2. Set the trigger type as shown below. Connecting the CY-15R or CY12-R/C (Three Way Triggering Function)When yo

2 USING THE UNIT SAFELY001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual...

20Example of Connections and Settingsuse three way triggering, you must use the “” and “” trigger types together. The “” trigger type cannot be used f

21Example of Connections and Settings Settings for Acoustic Drum TriggersOnce you have attached the trigger, proceed with the settings.1. Set the tri

22Example of Connections and Settings7. Set the Mask Time.Used mainly with the kick pedal, this prevents rebound of the beater from causing sounds to

23Example of Connections and SettingsOther Ways to Use the TMC-6 Connecting to a Multitrack RecorderBy taking the sounds of the kick, snare and other

24Parameter ListMIDI Parameters and Trigger Parametersfig.06-001.eIn many cases, if pads are connected so that their triggers are being detected prope

25Parameter List, (LOG1, LOG2) Compared to Linear, wider volume change will occur for softer hits.fig.06-017 (SPLINE) Variation in striking force

26Parameter ListWhen used as a controller:VELOCITY CURVE(Same as TRIG 1–6)This value becomes effective when Pedal Control is set to or .MIDI NOTE No

27Parameter ListTRIG TYPE (TRIGGER TYPE)This selects the kind of pad to be connected.Scan Time, Retrigger Cancel, and Mask Time change automatically w

28Parameter ListRETRIG CANCEL (RETRIGGER CANCEL)1–16Playing snare drum pads and other devices with commercially available acoustic drum triggers attac

29MIDI Implementation Chartfig.MIDI-Chart.eFunction...BasicChannelModeNoteNumber :VelocityAfterTouchPitch BendControlChange1–3164–95ProgramChangeSyste

3 011 • Do not allow any objects (e.g., flammable material, coins, pins); or liquids of any kind (water, soft drinks, etc.) to penetrate the unit...

30SpecificationsNumber of Memories12Display7 segments, 3 characters (LED)ConnectorsTrigger Input Jacks x 6 (7 Inputs), MIDI OUT Connector, AC Adaptor

IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.BLUE: BROWN: As the colours of the wires in the mains lead

InformationWhen you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.As of

4 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Power Supply 3

5 Table of Contents IMPORTANT NOTES...4Table of Contents...

6 Panel Descriptions Front Panel fig.01-01 1. TRIGGER INPUT INDICATOR Depending on the mode, the indicators behave as described below. In Play mode:

7 Panel Descriptions Rear panel fig.01-02 1. Cord Hook Anchor the power cord. 924 * To prevent the inadvertent disruption of power to your unit (shou

8 Connecting the TMC-6 Attaching the TMC-6 to a Drum Stand You can attach the TMC-6 to a drum stand (optional). 1. Attach the stand holder to the TMC

9 Connecting the TMC-6 TRIG 1/2/3/4/5 Connect optional pads, drum triggers, foot switches, or other such devices.When using a stereo cable to connect