Roland XP-30 Manual de usuario Pagina 188
- Pagina / 216
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
188
MIDI Implementation
2. Data transmission (sound source section)
■ Channel Voice Messages
● Note Off
status 2nd byte 3rd byte
8nH kkH vvH
n=MIDI channel: 0H - FH (ch.1 - ch.16)
kk=Note Number: 00H - 7FH (0 - 127)
vv=Note Off Velocity: 00H - 7FH (0 - 127)
● Note On
status 2nd byte 3rd byte
9nH kkH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
kk=note number: 00H - 7FH (0 - 127)
vv=Note On velocity: 01H - 7FH (1 - 127)
● Control Change
* By selecting a controller number that corresponds to the setting of the Assign parameter
(SYSTEM/CONTROL/CONTROL PEDAL) or each Assign parameter of C1–4 Slider
(SYSTEM/CONTROL/ASSIGN), you can transmit any desired control change.
❍Bank Select (Controller number 0,32)
status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm,ll=Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* This message is not transmitted if Program parameter (SYSTEM/MIDI/TRANSMIT
MIDI) or Bank Sel parameter (SYSTEM/MIDI/TRANSMIT MIDI) is OFF.
* For the Bank Select that corresponds to each Patch, refer to section 1.
* This message is not transmitted in GM mode
❍Modulation (Controller number 1)
status 2nd byte 3rd byte
BnH 01H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Modulation Depth: 00H - 7FH (0 - 127)
❍Breath type (Controller number 2)
status 2nd byte 3rd byte
BnH 02H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127)
❍Foot Type (Controller number 4)
status 2nd byte 3rd byte
BnH 04H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127)
❍Portamento Time (Controller number 5)
status 2nd byte 3rd byte
BnH 05H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Portamento Time: 00H - 7FH (0 - 127)
❍Volume (Controller number 7)
status 2nd byte 3rd byte
BnH 07H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Volume: 00H - 7FH (0 - 127)
❍Balance (Controller number 8)
status 2nd byte 3rd byte
BnH 08H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Balance: 00H - 7FH (0 - 127)
❍Panpot (Controller number 10)
status 2nd byte 3rd byte
BnH 0AH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=panpot: 00H - 40H - 7FH (left - center - right)
❍Expression (Controller number 11)
status 2nd byte 3rd byte
BnH 0BH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Expression: 00H - 7FH (0 - 127)
❍Hold 1 (Controller number 64)
status 2nd byte 3rd byte
BnH 40H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍Portamento (Controller number 65)
status 2nd byte 3rd byte
BnH 41H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍Sostenuto (Controller number 66)
status 2nd byte 3rd byte
BnH 42H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍Soft (Controller number 67)
status 2nd byte 3rd byte
BnH 43H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
❍ Hold 2 (Controller number 69)
status 2nd byte 3rd byte
BnH 45H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 7FH (0 - 127)
❍Sound Controller 2 (Controller number 71)
status 2nd byte 3rd byte
BnH 47H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
❍Sound Controller 3 (Controller number 72)
status 2nd byte 3rd byte
BnH 48H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
❍Sound Controller 4 (Controller number 73)
status 2nd byte 3rd byte
BnH 49H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
❍Sound Controller 5 (Controller number 74)
status 2nd byte 3rd byte
BnH 4AH vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-64 - 0 - +63)
❍General Purpose Controller 5 (Controller number 80)
status 2nd byte 3rd byte
BnH 50H vvH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
- OWNER’S MANUAL 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- SAVE THESE INSTRUCTIONS 2
- USING THE UNIT SAFELY 4
- Important Notes 5
- Contents 10
- Main Features 11
- Front and Rear Panel 12
- ■ Rear Panel 14
- Quick Start 15
- Getting Ready 16
- “Turning On the Power” (p 18
- “Turning Off 19
- Outil d'installation 22
- “Turning 23
- Off the Power” (p. 26) et 23
- Making Connections 24
- “Connecting to Your 25
- Computer” (p. 134) 25
- Turning On the Power 26
- (Factory Reset) 27
- Listening to the Demo Song 28
- ■ Profile of the Composer 29
- Playing the Sounds 30
- (Patch Search Function) 32
- Try Out Performance Functions 34
- ■ Hold Pedal 35
- ■ Expression Pedal 35
- ■ Portamento 35
- 516 2,4,5,7 36
- Advanced Use 39
- XP-30 Configuration 40
- Performance 41
- Basic Operation 42
- ■ About the Function Buttons 43
- ■ About the Cursor Buttons 44
- ■ Modifying a Value 45
- ■ Assigning a Name 46
- Chapter 2. Playing 47
- Chapter 2 49
- Playing in Performance Mode 51
- ■ Playing Along with a Song 53
- Playback (XP-30 Used as a 53
- Multitimbral Sound Source) 53
- Sound in Realtime 54
- (Sound Palette Function) 54
- Playing in Rhythm Set Mode 55
- Playing an Arpeggio 56
- ■ Playing an Arpeggio Over a 57
- Preset Keyboard Area 57
- Using a Hold Pedal 58
- Convenient Functions for 59
- Semitone Steps (Transpose) 60
- Note Does Not Sound (Panic) 60
- Regarding Effects 61
- Sound Editing Procedures 62
- Note on Tone Editing 64
- ■ Editing a Performance 65
- ■ Editing a Rhythm Set 66
- Keeping Edited Sound 67
- Functions of Patch Parameters 68
- VELOCITY (Velocity Range) 69
- KEY RANG (Key Range) 70
- STRUCT (Structure) 70
- (EFFECTS) 71
- PATCH CHORUS 72
- Sounds Are Played (CONTROL) 73
- RxSWITCH (Receive Switch) 74
- PEAK & HOLD 74
- CONTROL SOURCE 75
- CONTROL 1–3 75
- ■ Modifying Waveform (WAVE) 76
- ■ Modulating Sounds (LFO) 78
- ■ Modifying Pitch (PITCH) 79
- Frequency 80
- T1 T2 T3 T4 81
- LOWER&UPPER 82
- LOWER UPPER 82
- Functions of Performance 83
- Parameters 83
- ■ Setting Effects for a 84
- Performance (EFFECTS) 84
- PERFORM CHORUS 85
- PERFORM REVERB 85
- ■ Controlling How a Rhythm 90
- Tone will Sound with 90
- Controllers (CONTROL) 90
- ■ Modifying Waveform of a 90
- Rhythm Tone (WAVE) 90
- ■ Changing the Volume and 92
- Stereo Location of a Rhythm 92
- Tone (TVA) 92
- Multi-Effects Types 93
- (EFX Parameter) 93
- 4: PHASER 94
- 5: SPECTRUM 94
- 6: ENHANCER 94
- 7: AUTO-WAH 95
- 8: ROTARY 95
- 9: COMPRESSOR 96
- 10: LIMITER 96
- 11: HEXA-CHORUS 96
- 15: STEREO-FLANGER 98
- 16: STEP-FLANGER 98
- 17: STEREO-DELAY 99
- 18: MODULATION-DELAY 99
- 19: TRIPLE-TAP-DELAY 100
- Chapter 3 101
- 20: QUADRUPLE-TAP-DELAY 101
- 21: TIME-CONTROL-DELAY 101
- 22: 2VOICE-PITCH-SHIFTER 102
- 23: FBK-PITCH-SHIFTER 102
- (Feedback Pitch Shifter) 102
- 27: OVERDRIVE→FLANGER 104
- 28: OVERDRIVE→DELAY 104
- 29: DISTORTION→CHORUS 104
- 34: ENHANCER→DELAY 106
- 35: CHORUS→DELAY 106
- 36: FLANGER→DELAY 106
- XP-30 Operating Environment 108
- Setup (System Parameters 108
- ■ Keyboard and Controllers 110
- Settings (CONTROL) 110
- ■ MIDI Settings (MIDI) 112
- ■ Phrase Preview Settings 113
- (PREVIEW) 113
- ■ Adjusting Tuning (TUNE) 113
- ■ Program Change (PGM CHNG) 114
- Installation Status of Wave 114
- Expansion Boards (INFO) 114
- About Utility/Card Mode 115
- Basic Procedure in Utility/ 115
- Card Mode 115
- Storing Sound Data in User 116
- Memory (WRITE) 116
- Copying Sound Source 117
- Settings (COPY) 117
- ■ Rhythm Set Copy 118
- Initializing Sound Source 119
- Settings (INIT) 119
- Transmitting Sound Settings 119
- ■ Transmitting Data to User 120
- Preventing User Memory 121
- Writing Operation (PROTECT) 121
- Memory Card-Related 121
- Settings (CARD) 121
- Loading a File from Memory 122
- Card into the XP-30 (LOAD) 122
- Saving Data to Memory Card 122
- Recalling Factory Default 123
- Settings (FACTORY RESET) 123
- Entering GM Mode 124
- Modifying GM Mode Settings 125
- GM CHORUS 126
- GM REVERB 126
- Convenient Functions in GM 127
- Mode (GM Utility) 127
- ■ Initializing GM Mode (INIT) 128
- Techniques for Using Patches 129
- Using the XP-30 to Play Live 131
- Using External MIDI Devices 132
- Chapter 6 133
- Selecting Patches 133
- Selecting Performances 133
- Selecting Rhythm Sets 133
- Apple Macintosh 134
- ■ Disconnecting the Keyboard 137
- (Local OFF) 137
- Appendices 139
- Troubleshooting 140
- Error Messages 142
- Quick Reference of Procedures 143
- ■ Controller Settings 144
- ■ Saving and Loading Data 145
- ■ Controlling External MIDI 145
- External MIDI Device 146
- Parameter List 147
- CONTROL Group (p. 73) 148
- WAVE Group (p. 76) 148
- LFO Group (p. 78) 148
- ■ Performance Parameters 150
- ■ Rhythm Set Parameters 151
- ■ GM Mode Parameters 153
- ■ EFX Parameters 154
- ■ System Parameters 158
- Waveform List 160
- INT-B (Internal B) 161
- ● XP-A Menu Waveforms 163
- ● XP-C Menu Waveforms 166
- Patch List 168
- ■ B.P.M. CONVERSION TABLE 174
- Rhythm Set List 177
- Performance List 181
- Arpeggio Style List 182
- MIDI Implementation 183
- 3. Parameter Address Map 190
- 4. Supplementary Material 199
- 10 02 00 00H 204
- 00 00H Patch Common 204
- MIDI Implementation Chart 206
- Specifications 207
- For PC (25-pin) 208
- Apparatus containing 215
- Lithium batteries 215
- Information 216
Relacionado con productos y manuales para Los dispositivos de entrada Roland XP-30
(148 paginas)
(48 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales