Roland Fantom-Xa Manual de usuario descargar pdf (Pagina 213)

213

About V-LINK

In the V-LINK screen, press [F3 (CLIP)] or [F4 (ALL)].

* For details on clips/palettes, dissolve time, color difference signals (Cb/Cr), refer to the Edirol DV-7PR manual.

* The Fantom-Xa does not support the Edirol DV-7PR’s dual stream mode.

V-LINK Parameters

Parameter

Value Explanation

Note Tx Ch

1–16 MIDI channel that will switch Edirol DV-7PR clips/palettes and will

control dissolve time

Clip 1 Note No. 0 (C -)–127 (G9) Pads 1–9 correspond to Edirol DV-7PR clips (or palettes).

We recommend that you set “Template Set” to “Note” and Clip1 Note

No. to the same value as the “Pad Base Note” setting. (Quick Setup; p.

118)

Dissolve Time OFF, CC01, CC05, CC07, CC10, CC11, CC71–74,

CC91–93, AFTERTOUCH (Channel Aftertouch)

Control change number that controls the dissolve time (time over which

the image switches)

Ctrl Tx Ch 1–16 MIDI channel that will control the Edirol DV-7PR color Cb/Cr, bright-

ness, and video effect switching

Play Speed Ctrl 0.0-1.0-2.0, 0.5-1.0-2.0, 0.0-1.0-4.0, 0.5-1.0-4.0,

0.0-1.0-8.0, 0.5-1.0-8.0, 0.0-1.0-16.0, 0.5-1.0-16.0,

0.0-1.0-32.0, 0.5-1.0-32.0, 0.0-2.0-4.0, 0.0-4.0-8.0,

0.0-8.0-16.0, 0.0-16.0-32.0, -2.0-1.0-4.0, -6.0-1.0-8.0

Range of video playback speed

The three values are the playback speeds (multiples of normal speed)

at the left, center, and right positions of the pitch bend.

Color Cb Ctrl OFF, CC01, CC05, CC07, CC10, CC11, CC71–74,

CC91–93, AFTERTOUCH (Channel Aftertouch)

Control change number that controls the Cb color of the image

Color Cr Ctrl Control change number that controls the Cr color of the image

Brightness Ctrl Control change number that controls the brightness of the image

VFX1–4 Ctrl Control change number that controls the video effect

* VFX2–4 are not supported by the Edirol DV-7PR.

Fade Ctrl

Control change number that controls the output fade

Clip Filter OFF, ON (

✔

) Checked clips can be switched. Enable/disable switching for each clip.

Resetting the Image

[F3 (CLIP)]

(Clip Reset)

Turn off the image (solid black).

[F4 (ALL)]

(All Reset)

The effect applied to the image will be reset, and brightness,

color difference, etc. will all return to the default value.

Using the Clip Filter

For example, suppose that of the rhythm set you input in the

part used for V-LINK (i.e., the part of the same number as the

Note Tx Channel), you want only the kick and snare to switch

clips. In this case, check only the clips that correspond to the

note numbers of the kick and snare. The clips will switch when

the kick or snare plays.

In the V-LINK SETUP screen, press [F1 (FILTER)].

The Clip Filter window appears.

fig.V-LINK-CF

2. Use [CURSOR] to select a clip.

3. Use the VALUE dial or [INC] [DEC] to add or remove the

check mark (✔).

Checked clips can be switched.

Fantom-Xa_e.book 213 ページ２００４年１０月２２日　金曜日　午後２時３分

1 2 ... 208 209 210 211 212 213 214 215 216 217 218 ... 263 264

Comentarios a estos manuales

Sin comentarios

Roland Fantom-Xa Manual de usuario Pagina 213

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos musicales Roland Fantom-Xa