Roland MIDI Implementation DP990F Manual de usuario

Busca en linea o descarga Manual de usuario para Los dispositivos de entrada Roland MIDI Implementation DP990F. Roland MIDI Implementation DP990F User Manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 32
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
1
MIDI Implementation
Model
Date
Version
DP990F, HP302, HP305,
HP307, HPi-6F, HPi-7F,
LX-10F, RG-1F, RG-3F
Sep.1,2010
1.00
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
1. Receive data
Channel Voice Messages
Note off
Status 2nd byte 3rd byte
8nH kkH vvH
9nH kkH 00H
n = MIDI channel number: 0H-FH (ch.1-ch.16)
kk = note number: 00H-7FH (0-127)
vv = note off velocity: 00H-7FH (0-127)
* For Drum Parts, these messages are received when Rx.NOTE OFF = ON for
each Instrument.
Note on
Status 2nd byte 3rd byte
9nH kkH vvH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
kk = note number: 00H-7FH (0-127)
vv = note on velocity: 01H-7FH (1-127)
* Not received when Rx.NOTE MESSAGE = OFF. (Initial value is ON)
* For Drum Parts, not received when Rx.NOTE ON = OFF for each Instrument.
Polyphonic Key Pressure
Status 2nd byte 3rd byte
AnH kkH vvH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
kk = note number: 00H-7FH (0-127)
vv = key pressure: 00H-7FH (0-127)
* Not received when Rx.POLY PRESSURE (PAf) = OFF. (Initial value is ON)
* The resulting effect is determined by System Exclusive messages. With the
initial settings, there will be no effect.
Control Change
* When Rx.CONTROL CHANGE = OFF, all control change messages except
for Channel Mode messages will be ignored.
* The value specified by a Control Change message will not be reset even by a
Program Change, etc.
Bank Select (Controller number 0, 32)
Status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
mm, ll = Bank number: 00H, 00H-7FH, 7FH (bank.1-bank.16384), Initial
Value = 00 00H (bank.1)
* Not received when Rx.BANK SELECT = OFF.
* Rx.BANK SELECT” is set to OFF by “GM1 System On,” and Bank Select
message will be ignored.
* Rx.BANK SELECT” is set to ON by “GM2 System On.”
* Rx.BANK SELECT” is set to ON by power-on Reset or by receiving “GS
RESET.”
* When Rx.BANK SELECT LSB = OFF, Bank number LSB (llH) will be handled
as 00H regardless of the received value. However, when sending Bank Select
messages, you have to send both the MSB (mmH) and LSB (llH, the value
should be 00H) together.
* Bank Select processing will be suspended until a Program Change message
is received.
* The GS format “Variation number” is the value of the Bank Select MSB
(Controller number 0) expressed in decimal.
* Some other GS devices do not recognize the Bank Select LSB (Controller
number 32).
Modulation (Controller number 1)
Status 2nd byte 3rd byte
BnH 01H vvH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
vv = Modulation depth: 00H-7FH (0-127)
* Not received when Rx.MODULATION = OFF. (Initial value is ON)
* The resulting effect is determined by System Exclusive messages. With the
initial settings, this is Pitch Modulation Depth.
Portamento Time (Controller number 5)
Status 2nd byte 3rd byte
BnH 05H vvH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
vv = Portamento Time: 00H-7FH (0-127), Initial value = 00H (0)
* This adjusts the rate of pitch change when Portamento is ON or when using
the Portamento Control. A value of 0 results in the fastest change.
Data Entry (Controller number 6, 38)
Status 2nd byte 3rd byte
BnH 06H mmH
BnH 26H llH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
Volume (Controller number 7)
Status 2nd byte 3rd byte
BnH 07H vvH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
vv = Volume: 00H-7FH (0-127), Initial Value = 64H (100)
* Volume messages are used to adjust the volume balance of each Part.
* Not received when Rx.VOLUME = OFF. (Initial value is ON)
Pan (Controller number 10)
Status 2nd byte 3rd byte
BnH 0AH vvH
n = MIDI channel number: 0H-FH (ch.1-ch.16)
vv = pan: 00H-40H-7FH (Left-Center-Right), Initial Value = 40H (Center)
* For Rhythm Parts, this is a relative adjustment of each Instrument’s pan
setting.
* Some Tones are not capable of being panned all the way to the left or right.
* Not received when Rx.PANPOT = OFF. (Initial value is ON)
Vista de pagina 0
1 2 3 4 5 6 ... 31 32

Indice de contenidos

Pagina 1 - MIDI Implementation

1MIDI Implementation Model: Date: Version: DP990F, HP302, HP305, HP307, HPi-6F, HPi-7F, LX-10F, RG-1F, RG-3F Sep.1,2010 1.00 Copyright © 2010 ROLAN

Pagina 2

103. Parameter Address Map (Model ID = 42H) This map indicates address, size, Data (range), Parameter, Description, and Default Value of parameters w

Pagina 3

11 02: Room 3 03: Hall 1 04: Hall 2 05: Plate 06: Delay 07: Panning Delay 40 01 31 00 00 01 00-07 REVERB CHARAC

Pagina 4 - ■Channel Mode Messages

12●Part Parameters This instrument has 16 parts. Parameters that can be set individually for each Part are called Part parameters. If you use exclusi

Pagina 5 - ■System Exclusive Message

13* “Rx.BANK SELECT” is set to OFF by “GM1 System On,” and Bank Select message will be ignored. * “Rx.BANK SELECT” is set to ON by “GM2 System On.”

Pagina 6

1440 2x 28 00 00 01 00-7F CAf LFO2 PITCH DEPTH 0-600 [cent] 00 0 [cent] 40 2x 29 00 00 01 00-7F CAf LFO2 TVF DEPTH 0-2400 [cent] 00

Pagina 7

154. Supplementary material ●Decimal and Hexadecimal table In MIDI documentation, data values and addresses/sizes of exclusive messages etc. are expr

Pagina 8 - 2. Transmit data

16●Example of an Exclusive message and calculating a Checksum Roland Exclusive messages are transmitted with a checksum at the end (before F7) to mak

Pagina 9 - ■System exclusive messages

175. Effect List 0100: Equalizer 0101: Spectrum 0102: Enhancer 0104: Isolator 0105: Low Boost 0106: High Pass Filter 0110: Overdrive 0111: Distortion

Pagina 10 - ■Individual Parameters

18● 0104: Isolator This is an equalizer which cuts the volume greatly, allowing you to add a special effect to the sound by cutting the volume in va

Pagina 11

19● 0107: Speaker Simulator Simulates the speaker type and mic settings used to record the speaker sound. No Parameter Value Description 1

Pagina 12 - ●Part Parameters

2○Expression (Controller number 11) Status 2nd byte 3rd byte BnH 0BH vvH n = MIDI channel number: 0H-FH (ch.1-ch.16) vv = Expression: 00H-7FH (0

Pagina 13

20● 0120: Phaser This is a stereo phaser. A phase-shifted sound is added to the original sound and modulated. No Parameter Value Description 1

Pagina 14 - ●Drum Setup Parameters

21● 0127: 3D Flanger This applies a 3D effect to the flanger sound. The flanger sound will be positioned 90 degrees left and 90 degrees right. No P

Pagina 15 - 4. Supplementary material

22● 0103: Humanizer Adds a vowel character to the sound, making it similar to a human voice. No Parameter Value Description 1 Drive Sw 0-1

Pagina 16 - ●About tuning

23● 0130: Compressor Flattens out high levels and boosts low levels, smoothing out fluctuations in volume. No Parameter Value Description 1 At

Pagina 17 - 5. Effect List

24● 0143: Space D This is a multiple chorus that applies two-phase modulation in stereo. It gives no impression of modulation, but produces a transp

Pagina 18

25● 012d: Rotary2 This type provides modified response for the rotary speaker, with the low end boosted further. This effect is a descendant of the R

Pagina 19 - ● 0107: Speaker Simulator

26● 015c: Stereo Delay2 This is a stereo delay. No Parameter Value Description 1 Delay Left Mode 0-1 ms, note When this is set to “note,”

Pagina 20 - ● 0123: Stereo Flanger

27● 015f: Stereo Delay5 This is a stereo delay. No Parameter Value Description 1 Delay Left Mode 0-1 ms, note When this is set to “note,” t

Pagina 21 - ● 0121: Auto Wah

28● 0157: 3D Delay This applies a 3D effect to the delay sound. The delay sound will be positioned 90 degrees left and 90 degrees right. No Parame

Pagina 22

29● 0175: Telephone No Parameter Value Description 1 Voice Quality #1 0-15 0-15 Audio quality of the telephone voice 2 Treble 0-30 -15 -

Pagina 23

3 ○Portamento control (Controller number 84) Status 2nd byte 3rd byte BnH 54H kkH n = MIDI channel number: 0H-FH (ch.1-ch.16) kk = source note

Pagina 24 - ● 0122: Rotary

30● 0206: Enhancer→Chorus This effect connects an enhancer and a chorus in series. No Parameter Value Description 1 Enhancer Sens 0-127 0-1

Pagina 25 - ● 015b: Stereo Delay1

31● 020a: Flanger→Delay This effect connects a flanger and a delay in series. No Parameter Value Description 1 Flanger Pre Delay 0-125 0.0-

Pagina 26 - ● 015e: Stereo Delay4

32MIDI Implementation Chart DIGITAL PIANO Date: Sep. 1, 2010 Model DP990F, HP302, HP305, HP307, HPi-6F, HPi-7F, LX-10F, RG-1F, R

Pagina 27 - ● 0152: Triple Tap Delay

4to specify the parameter to be controlled, and then use Data Entry messages to specify the value of the specified parameter. Once an RPN parameter h

Pagina 28 - ● 0172: Lo-Fi

5BnH 7DH 00H n = MIDI channel number: 0H-FH (ch.1-ch.16) * OMNI ON is only recognized as “All notes off”; the Mode doesn’t change (OMNI OFF remai

Pagina 29

6 Byte Explanation F0H Exclusive status 41H ID number (Roland) 10H Device ID (dev: 00H-1FH (1-32), Initial value is 10H (17)) 42H Mod

Pagina 30 - ● 0209: Chorus→Delay

7Status Data byte Status F0H 7FH, 7FH, 09H, 01H, 0nH, ppH, rrH F7H Byte Explanation F0H Exclusive status 7FH ID number (Universal Re

Pagina 31 - ● 0040: Damper Resonance

8aaH Address MSB: upper byte of the starting address of the transmitted data bbH Address: middle byte of the starting address of the tran

Pagina 32 -

9 System exclusive messages ○Identity Reply Status Data byte Status F0H 7EH, 10H, 06H, 02H, 41H, vvH,,vvH, nnH, nnH, rrH, rrH, rrH, rrH

Comentarios a estos manuales

Sin comentarios