R
®
System Version Procedures
©2008 Roland Corporation U.S. Page
RA-800 Power on while holding the F1 button to the right of the display
RC-50
Power on while holding PARAMETER Left and Right.
RD-300GX Power on while holding SOUND CONTROL
RD-300SX With the unit on, hold down EDIT and WRITE and press SOUND CONTROL
RD-500 Power on while holding SYNTH, E.GRAND, MKS-20 and the NUMBER 8 button
RD-600 Power on while holding INTERNAL TONE VARIATION 1, PART SELECT TX LOWER, and
PART SELECT TX UPPER
RD-700GX Power on while holding V-LINK
RD-700/SX With the unit on, press the EDIT button while pressing both the CURSOR RIGHT and
PART SELECT(LOWER) buttons Power off when done
RS-5/9 Power on while holding PERFORM TONE, USER/PRESET and 1/PIANO
RS-50/70 Power on while holding DESTINATION TONE, ENV, and TAP TEMPO
RSP-550 Power on while holding PROGRAM/PAGE DOWN (v), VALUE DOWN (v), PARM and
CONTROL
RSS-10 Power on while holding DEVICE ID and FUNCTION. Press DEMO PROGRAM
RSS-303 With unit powered on, simultaneously press LEVEL, USER PROGRAM 3 and SETUP
RV-70 Power on while holding UP (^), DOWN (v) and WRITE. Press UP (^)
S
Model Procedure
S-10 Power on while holding PERFORMANCE and MIDI
S-50 Connect the S-50 to a CRT, then turn CRT power on. Turn on the S-50 and insert the
system disk (only ver. 1.01 to 1.09 will work). Press FUNCTION, then the “P1” button.
Press SHIFT, then the #1 button on the ten-key pad. Press ENTER
S-220 Power on while holding PERFORM and MIDI
S-330 Connect the S-330 to a CRT, then turn CRT power on. Turn on the S-330 and insert the
system or utility disk. Press MODE, press the DOWN (v) button three times, then
EXECUTE. Press the DOWN (v) button once, then EXECUTE. Press MENU, then press
DEC/NO twice
S-550 Connect the S-550 to a CRT, then turn CRT power on. Turn on the S-550 while holding
the #1 button. (Hold until you see “Please Insert System Disk.”) Insert the system or
utility disk. When display says, “Load next disk?”, press DEC/NO. Press FUNC, then MENU.
Press the DOWN (v) button, then EXECUTE. Press MENU, then the #1 button. Press
DEC/NO twice
S-750/760/770 Power on
SB-55 Press the POWER button to make the STANDBY light come on. While holding PROG and
SET, press REW and FF
SBX-1000 Power on while holding SETUP and TIMECODE INT/EXT
SC-33 Power on while holding LOW/SUB, UTILITY and NUMBER DOWN (v)
SC-50 Press the POWER button to make the STANDBY light come on. While holding both
INSTRUMENT buttons, press both MIDI CH buttons
SC-55/55MKII Press the POWER button to make the STANDBY light come on. While holding both
INSTRUMENT buttons, press both MIDI CH buttons
SC-88 Power on while holding both MIDI CH buttons, then press the PREVIEW knob immediately
SC-155 Press the POWER button to make the STANDBY light come on. While holding both
INSTRUMENT buttons, press both MIDI CH buttons
SC-880 Power on while holding SYSTEM, WRITE and EXIT
SD-35 Power on while holding PAUSE, PROG and REPEAT
SDE-330 Power on
SDX-330 Power on
SE-50 Power on while holding NUMBER DOWN (v), VALUE DOWN (v) and UTILITY. Press WRITE
SE-70 Power on while holding EXIT and UTILITY. Press UTILITY, then PARAMETER LEFT (<).
Press PARAMETER RIGHT (>), then CONTROL 1
SN-700 Power on while holding CH-A of NOISE CANCEL and CH-A of HUM CANCEL
(228 paginas)
(64 paginas)
(224 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales