Roland KF-7 Manual de usuario descargar pdf (Pagina 4)

●

Pitch Bend Change

Status 2nd byte 3rd bytes

EnH llH mmH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

* Not received when Rx.PITCH BEND = OFF. (Initial value is ON)

* The resulting effect is determined by System Exclusive messages. With the initial

settings the effect is Pitch Bend.

■

Channel Mode Messages

●

All Sounds Off (Controller number 120)

Status

2nd byte 3rd bytes

BnH 78H 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* When this message is received, all currently-sounding notes on the corresponding

channel will be turned off immediately.

●

Reset All Controllers (Controller number 121)

Status

2nd byte 3rd bytes

BnH 79H 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* When this message is received, the following controllers will be set to their reset values.

Controller Reset value

Pitch Bend Change ±0 (Center)

Polyphonic Key Pressure 0 (off)

Channel Pressure 0 (off)

Modulation 0 (off)

Expression 127 (max)

Hold 1 0 (off)

Portamento 0 (off)

Sostenuto 0 (off)

Soft 0 (off)

RPN unset; previously set data will not change

NRPN unset; previously set data will not change

●

Local Control (Controller number 122)

Status

2nd byte 3rd bytes

BnH 7AH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Control value: 00H, 7FH (0,127), 00H: Local Off, 7FH: Local On

●

All Notes Off (Controller number 123)

Status

2nd byte 3rd bytes

BnH 7BH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* When All Notes Off is received, all notes on the corresponding channel will be turned

off. However if Hold 1 or Sostenuto is ON, the sound will be continued until these are

turned off.

●

OMNI OFF (Controller number 124)

Status

2nd byte 3rd bytes

BnH 7CH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* The same processing will be carried out as when All Notes Off is received.

●

OMNI ON (Controller number 125)

Status

2nd byte 3rd bytes

BnH 7DH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* OMNI ON is only recognized as “All notes off”; the Mode doesn’t change (OMNI OFF

remains).

●

MONO (Controller number 126)

Status 2nd byte 3rd bytes

BnH 7EH mmH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm = mono number: 00H-10H (0-16)

* The same processing will be carried out as when All Sounds Off and All Notes Off is

received, and the corresponding channel will be set to Mode 4 (M = 1) regardless of the

value of “mono number.”

●

POLY (Controller number 127)

Status 2nd byte 3rd bytes

BnH 7FH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

* The same processing will be carried out as when All Sounds Off and All Notes Off is

received, and the corresponding channel will be set to Mode 3.

■

System Realtime Message

●

Realtime Clock

Status

F8H

●

Start

Status

FAH

●

Continue

Status

FBH

●

Stop

Status

FBH

●

Active Sensing

Status

FEH

* When Active Sensing is received, the unit will begin monitoring the intervals of all

further messages. While monitoring, if the interval between messages exceeds 420 ms,

the same processing will be carried out as when All Sounds Off, All Notes Off and Reset

All Controllers are received, and message interval monitoring will be halted.

■

System Exclusive Message

Status

Data byte Status

F0H iiH, ddH, ......, eeH F7H

F0H: System Exclusive Message status

ii = ID number: an ID number (manufacturer ID) to indicate the manufacturer whose

Exclusive message this is. Roland’s manufacturer ID is 41H.

ID numbers 7EH and 7FH are extensions of the MIDI standard; Universal

Non-realtime Messages (7EH) and Universal Realtime Messages (7FH).

dd,...,ee = data: 00H-7FH (0-127)

F7H: EOX (End Of Exclusive)

The System Exclusive Messages received by this instrument are; messages related to mode

settings, Universal Realtime System Exclusive messages and Data Set (DT1).

●

System exclusive messages related to mode settings

These messages are used to initialize a device to GS or General MIDI mode, or change the

operating mode. When creating performance data, a “GM1 System On” message should be

inserted at the beginning of a General MIDI 1 score, a “GM2 System On” message at the

beginning of a General MIDI 2 score, and a “GS Reset” message at the beginning of a GS

music data. Each song should contain only one mode message as appropriate for the type of

data. (Do not insert two or more mode setting messages in a single song.)

“GM System On” uses Universal Non-realtime Message format. “GS Reset” uses Roland

system Exclusive format “Data Set 1 (DT1).”

1 2 3 4 5 6 7 8 9 ... 27 28

Comentarios a estos manuales

Sin comentarios

Roland KF-7 Manual de usuario Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos musicales Roland KF-7