Roland TD-8 Manual de usuario descargar pdf (Pagina 206)

204

MIDI-Implementation

❍Foot control (Controller number 4)

Status 2nd byte 3rd byte

BnH 04H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127)

* This is transmitted only on the channel which is assigned to the drum kit part.

* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC is set to

“FOOT”.

❍Data Entry (Controller number 6)

Status 2nd byte 3rd byte

BnH 06H mmH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

mm = The value of the parameter specified by RPN.

* Only the channel assigned to the backing part are sent.

* When a pattern or a song are selected or adjust [PATTERN]-[PART]-[SETUP]-[PAGE 2]

BEND RANGE setting, the pitch bend sensitivity of the sequencer pattern data will be

transmitted.

Values for the RPN parameter, on the normal mode of TD-8, are as follows.

RPN Data entry

MSB LSB MSB LSB Explanation

00H 00H mmH --- Pitch Bend Sensitivity

mm: 00H - 18H (0 - 24 semitones)

7FH 7FH --- --- RPN null

set condition where RPN is unspecified.

❍Volume (Controller number 7)

Status 2nd byte 3rd byte

BnH 07H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Volume: 00H - 7FH (0 - 127)

* Only the channel assigned to the percussion part and the backing part are sent.

* When a pattern or a song are selected, the part level of the sequencer pattern data will be

transmitted.

❍Pan (Controller number 10)

Status 2nd byte 3rd byte

BnH 0AH vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = pan: 00H - 40H - 7FH (Left - Center - Right)

* Only the channel assigned to the backing part are sent.

* When a pattern or a song are selected, the pan of the sequencer pattern data will be

transmitted.

❍General purpose controller 1 (Controller number 16)

Status 2nd byte 3rd byte

BnH 10H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127)

* This is transmitted only on the channel which is assigned to the drum kit part.

* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or

ZONE CC are set to “GEN1”.

❍General purpose controller 2 (Controller number 17)

Status 2nd byte 3rd byte

BnH 11H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127)

* This is transmitted only on the channel which is assigned to the drum kit part.

* This will be transmitted if the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or

ZONE CC are set to “GEN2”.

❍Hold 1 (Controller number 64)

Status 2nd byte 3rd byte

BnH 40H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF 64-127 = ON

* Only the channel assigned to the backing part are sent.

* Transmitted only when the TD-8 is in play for Pattern in which Hold 1 is recorded.

❍Effect 1 (Reverb Send Level) (Controller number 91)

Status 2nd byte 3rd byte

BnH 5BH vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Reverb send level: 00H - 7FHÅi0 - 127Åj

* Only the channel assigned to the percussion part and backing part are sent.

* When a pattern or a song are selected, the reverb send level of the sequencer pattern data

will be transmitted.

❍RPN MSB/LSB (Controller number 101,100)

Status 2nd byte 3rd byte

BnH 65H mmH

BnH 64H llH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

mm = upper byte of parameter number specified by RPN (MSB)

ll = lower byte of parameter number specified by RPN (LSB)

* Only the channel assigned to the backing part are sent.

* When a pattern or a song are selected, the pitch bend sensitivity of the sequencer pattern

data will be transmitted.

* Regarding the RPN please refer to p. 201.

Values for the RPN parameter, on the normal mode of TD-8, are as follows. Regarding the

value of each parameter, refer to Data Entry (Controller number 6).

RPN

MSB LSB

Parameter

00H 00H Pitch Bend Sensitivity

7FH 7FH RPN null

● Program Change

Status 2nd byte

CnH ppH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

pp = Program number: 00H - 7FH (prog.1 - prog.128)

* Not transmitted when [SETUP]-[MIDI]-[PROG] PROGRAM CHANGE RX SW is set to

“OFF”.(Initial Value is ON)

* Program changes corresponding to drum kit are sent when drum kits are selected.

* Program changes corresponding to each part’s instrument are sent when songs or

patterns are selected. Also, when instruments are selected for parts, program changes for

the respective instruments are sent.

● Pitch Bend Change

Status 2nd byte 3rd byte

EnH llH mmH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

* Only the channel assigned to the backing part are sent.

* Transmitted only when the TD-8 is in play for pattern in which pitch bend change is

recorded.

■ System Realtime Message

● Timing Clock

Status

F8H

● Start

Status

FAH

1 2 ... 201 202 203 204 205 206 207 208 209 210 211 ... 223 224

Roland TD-8 Manual de usuario Pagina 206

Comentarios a estos manuales

Roland TD-8 Manual de usuario Pagina 206

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos musicales Roland TD-8