Roland LEC-330 Guia de preparacion

Setup GuideRead this rst. This describes the setup tasks and important conditions about the installation location that must be met in order to enable

To Ensure Safe Use8Warning labels are afxed to make areas of danger immediately clear. The meanings of these labels are as follows. Be sure to heed

9 Pour utiliser en toute sécuritéLa manipulation ou l'utilisation inadéquates de cet appareil peuvent causer des blessures ou des dommages matéri

Pour utiliser en toute sécurité10 L'utilisation incorrecte peut causer des blessures ATTENTIONS'assurer de suivre les procédures d'u

Pour utiliser en toute sécurité11 PRUDENCENe jamais grimper ni s'appuyer sur la machine.La machine n'est pas conçue pour sup-porter le

Pour utiliser en toute sécurité12 ATTENTIONManipuler le câble d'alimentation, la che et la prise électrique correcte-ment et avec soin.Ne jam

Pour utiliser en toute sécurité13 Remarques importantes à propos du câble d'alimentation, de la che et de la prise électriqueNe jamais déposer

Pour utiliser en toute sécurité14 L'encre, les liquides nettoyants et les liquides usées sont inammables et toxiques En cas d'ingestion ou

Pour utiliser en toute sécurité15 Cet appareil utilise des rayons ultraviolets. Attention : Rayonnement ultravioletCet appareil est muni de couve

Pour utiliser en toute sécurité16Des vignettes d'avertissement sont apposées pour qu'il soit facile de repérer les zones dangereuses. La si

17Setup Guide

Thank you very much for purchasing this product. To ensure correct and safe usage with a full understanding of this product's performance, pleas

181. Installation EnvironmentDeciding On an Installation SiteInstall in a quiet, stable location oering good operating conditions. An unsuitable loca

1. Installation Environment19Temperature and HumidityMaintain the specied temperature and humidity even when the machine is not in use. If temperatu

1. Installation Environment20Installation SpaceThe space shown in the gure is required in order to use this machine.Air VentilationThis machine emit

21* The long media clamps are installed on the machine. 2. Included ItemsThe following items are packed together with the unit. Make sure they are a

2 Included Items22SOL INK cleaning cartridgesHexagonal wrench (5 mm)Head-unit tool Software RIPUser's ManualSetup guide(This document)White and

3. Assembling and InstallingStep 1: Assemble the Stand WARNING Unpacking and installation must be carried out by six or more persons.Otherwise

3. Assembling and Installing24Tighten the remaining bolts.Fully tighten all bolts to secure the stay and stand legs completely.After assembling, lo

3. Assembling and Installing25Mount the rail slider on the stand legs and secure it in place with the bolts.Line up the tab with the slot in the rail

3. Assembling and Installing26Attach the dancer roller.Secure in place using bolts, working on the right side rst.4.Attach the shafts and engage the

3. Assembling and Installing27Place the shafts on the stand and engage the brake.5.Attach the paper tube.Pull the dancer roller back toward you. En

1ContentsCompany names and product names are trademarks or registered trademarks of their respective holders.http://www.rolanddg.com/Copyright © 2009

3. Assembling and Installing28Mount the paper tube and secure the arm in place.First, t the paper tube securely onto the end cap on the same side as

3. Assembling and Installing29Step 2: Mount the Machine WARNING Unpacking and installation must be carried out by six or more persons.Otherwis

3. Assembling and Installing30Step 3: Install the Drain BottleProcedureRemove the drain-tube cover and attach the bottle stand.Attach the drain-tube c

3. Assembling and Installing31Remove the lid from the drain bottle.Carefully store the lid and inner cap so that they will not be misplaced.From the

3. Assembling and Installing32Step 4: Remove the Packing MaterialsPacking materials are attached to the machine to protect it from vibration during tr

3. Assembling and Installing33You can attach the removed packing materials at the location shown in the gure for storage. Bottom surface of the main

3. Assembling and Installing34Step 5: Attach the Rear CoverProcedureSecure the left and right rear-cover stays in place with the screws.Use a commerc

3. Assembling and Installing35Step 6: Attach the Media GuideProcedureMove the dancer roller toward the rear.Secure the media guide in place with scr

364. Connecting the CablesConnecting the Cable of the Take-up UnitPeel off the tape.Pass the take-up unit cable through at the locations shown in th

4. Connecting the Cables37Connecting the Power Cord and the Network Cable WARNING Connect to electrical outlet that complies with this machine'

2 To Ensure Safe UseImproper handling or operation of this machine may result in injury or damage to prop-erty. Points which must be observed to preve

385. Installing the Ink Cartridges(LEC-300A)Filling with Ink for the First TimeSpecial procedures are required when installing ink cartridges for the

5. Installing the Ink Cartridges (LEC-300A)391. Switch on the power and make the initial settings.Close the front cover.Switch on the main power sw

5. Installing the Ink Cartridges (LEC-300A)402.Clean the print heads using the SOL INK cleaning cartridge.Press .Make sure the drain bottle is ins

5. Installing the Ink Cartridges (LEC-300A)413.Insert the ink cartridges for the respective colors. Before you insert the ink cartridge for each col

426. Installing the Ink Cartridges (LEC-330)Filling with Ink for the First TimeSpecial procedures are required when installing ink cartridges for the

6. Installing the Ink Cartridges (LEC-330)43Selecting the Ink ModeBe sure to make the selection of the ink mode when switching on the power for the 

6. Installing the Ink Cartridges (LEC-330)44When Selecting Cyan, Magenta, Yellow, Black, Gloss, GlossClose the front cover.If the main power switch

6. Installing the Ink Cartridges (LEC-330)45When Selecting Cyan, Magenta, Yellow, Black, Gloss, WhiteClose the front cover.If the main power switch

6. Installing the Ink Cartridges (LEC-330)46Installing the Ink CartridgesDuring cleaning, you insert and remove cartridges several times. The on-scre

6. Installing the Ink Cartridges (LEC-330)472.Clean the print heads using the SOL INK cleaning cartridge.Make sure the selected ink mode is enabled.

To Ensure Safe Use3 Incorrect operation may cause injury WARNINGBe sure to follow the operation pro-cedures described in this documenta-tion. Never a

6. Installing the Ink Cartridges (LEC-330)48Pull out the cleaning cartridges.When this screen appears, cleaning is nished.Make sure the drain bott

6. Installing the Ink Cartridges (LEC-330)49Make sure the drain bottle is installed.Press.When this screen appears, lling with ink is n-i

507. Installing the Blade CAUTION Be sure to perform operations as specied by these instructions, and never touch any area not specied in the instr

7. Installing the Blade51Open the front cover.When this screen appears, preparation is completed.3.Install the blade holder.Loosen the screw shown i

528. Network SettingsIntroductionThis machine has a built-in print server as a network interface. When you use the print server, you can send printing

8. Network Settings53For Windows 2000:From the [Start] menu, click [Settings], then click [Network and Dial-up Con-nections].Double-click the [Local A

8. Network Settings54In the [Local Area Connection Properties] dialog box, click [OK], then in the [Local Area Connection Status] dialog box, click [

8. Network Settings552.Set the subnet mask.Press .Press twice.Use to select the address number.[Subnet mask] : 255.255.255.000Note: For the subnet

8. Network Settings56Press .Repeat  and  to set the gateway address numbers.When you've nished making the setting, press.Press

579. Installation of Ventilating EquipmentVentilating Equipment? P. 20, “Air Ventilation.”In preparing ventilating devices, please note the following

To Ensure Safe Use4 Danger of electrical short, shock, electrocution, or reRatings WARNINGConnect to an electrical outlet that complies with t

9. Other Items to Have on Hand58Attach the hose to the connection port on the unit.Insert all the way.

59

60

61

62

63

64

R1-091026

To Ensure Safe Use5 Important notes about the power cord, plug, and electrical outletNever place any object on top or subject to damage.Never bend or

To Ensure Safe Use6 Ink, cleaning uid, and discharged uid are ammable and toxic In the event of ingestion or physical distress In the event of co

To Ensure Safe Use7 This machine weighs 210 kg (463 lb.). Media weighs 20 kg (44 lb.). WARNINGInstall the machine in a location that is level, stable